Search:

Type: Posts; User: RDP; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    5
    Views
    1,411

    Question: Roger, Sam shows how to do it here, at 6:10...

    Roger, Sam shows how to do it here, at 6:10 :thumbsup:

    https://youtu.be/3s9hOGwUF-s

    Richard.
  2. Replies
    8
    Views
    1,179

    Help, please: Doc, I use this thumb drive, no problem, just...

    Doc, I use this thumb drive, no problem, just drag and drop one way or the other, ��
    ...
  3. Replies
    113
    Views
    14,688

    Critique Request: :banana:Congratulations!! Danae, :happyvise: very...

    :banana:Congratulations!! Danae, :happyvise: very well deserved recognition,

    Richard.
  4. Replies
    18
    Views
    3,422

    Critique Request: Thank you, should start engraving this side next...

    Thank you, should start engraving this side next week,

    Richard.
  5. Thread: Dinosaur

    by RDP
    Replies
    11
    Views
    1,448

    Layne, I just do this as a hobby and do not...

    Layne,
    I just do this as a hobby and do not understand 99% per cent of my IPad, but using Procreate has made my drawing experience 100 times better, you
    have just seen my results, what would and...
  6. Replies
    18
    Views
    3,422

    Critique Request: Thanks to all the likes and,Thanks Layne, sorry...

    Thanks to all the likes and,Thanks Layne, sorry about the pics, there are not the best, I should explain I just took them with my cell phone from the IPad at work I was so happy with the result I had...
  7. Replies
    18
    Views
    3,422

    Critique Request: Thank you Weldon, woo-whooo :banana:, very...

    Thank you Weldon, woo-whooo :banana:, very encouraging words!!, I know I have a lot to learn and won't let it go to my head, you have been most helpful and I very much appreciate it, you have helped...
  8. Replies
    18
    Views
    3,422

    Critique Request: Ok , had a bit of a play today and this is what I...

    Ok , had a bit of a play today and this is what I came up with, and thought I try a preview of how it may look when cut ;) that is if I do it right, ;) what do you think?
    Richard.4144841449

    Sent...
  9. Replies
    18
    Views
    3,422

    Critique Request: Thanks Bill And Layne, yes there are some...

    Thanks Bill And Layne, yes there are some adjustments to be made for sure, I am revising the drawing again and will post pic later, thanks for pointing out needed changes guys, I agree with all of...
  10. Replies
    18
    Views
    3,422

    Critique Request: I have revised my drawing and altered it some as...

    I have revised my drawing and altered it some as suggested, I think is an improvement from the first one, but I don't think is quite there yet, any comments?
    I have re attached the first one as...
  11. I am not an NRA member, I just google A Rifleman...

    I am not an NRA member, I just google A Rifleman May 2017 and this came up, awesome work!!

    http://www.nxtbook.com/nxtbooks/nra/ar_201705/#/32

    Richard.
  12. Replies
    18
    Views
    3,422

    Critique Request: Thank you Weldon, if you say is looking good, who...

    Thank you Weldon, if you say is looking good, who am I to argue with a Master!!, I definitely will try to improve it before I start cutting, thank you for taken the time to comment,
    Love your work...
  13. Works for me as well, awesome photos, thank you...

    Works for me as well, awesome photos, thank you Brian.

    Richard.
  14. Replies
    18
    Views
    3,422

    Critique Request: Thanks Bill, I see what you mean, it did look...

    Thanks Bill, I see what you mean, it did look kind of odd to me just couldn't put my finger on it, also noticed I did not allow for the front raised section same as the rear one near the hammer screw...
  15. Replies
    18
    Views
    3,422

    Critique Request: The project continues

    It has been a long time but I think I can finally get back to my restoration and engraving project,
    http://www.engraverscafe.com/showthread.php?17406-A-piece-of-American-History-down-under

    hope...
  16. Replies
    7
    Views
    1,448

    I have both, micro and ultra micro grain, thanks...

    I have both, micro and ultra micro grain, thanks to Carlos, I don't know now, but when I ordered them a year or so ago, they did not ship outside of the USA. gracias hermano.:thumbsup:
    My opinion is...
  17. Thread: Geometric Shapes

    by RDP
    Replies
    10
    Views
    2,739

    http://procreate.si/forums/index.php?topic=438.0...

    http://procreate.si/forums/index.php?topic=438.0

    Posted this some time ago.

    Richard.

    Sent from my SM-G900I using Tapatalk
  18. Thread: Happy birthday JJ

    by RDP
    Replies
    15
    Views
    1,974

    Happy birthday JJ :banana::happyvise::banana: ...

    Happy birthday JJ :banana::happyvise::banana:

    Richard.
  19. Replies
    18
    Views
    3,094

    Welcome to the forum Jon, a lot of good advice...

    Welcome to the forum Jon, a lot of good advice here, I just do it as a hobby and what I do is self taught, and not very good :), it will get frustrating a lot of times but keep at it and you'll get...
  20. Thread: The Warden

    by RDP
    Replies
    5
    Views
    1,564

    Thank you friend, the chain mail is just a small...

    Thank you friend, the chain mail is just a small piece I roughly made to try out after I saw a you tube video, I had some jump rings that are left over from coils we make at work, and thought to...
Results 1 to 20 of 100
Page 1 of 5 1 2 3 4


GRS Skyscraper


Download Videos


Drawing Scrolls


Lee Griffiths

Cafe page views since 18-Nov-2006.