Search:

Type: Posts; User: jerrywh; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    15
    Views
    1,181

    When I started I bought one and it would not...

    When I started I bought one and it would not focus correctly. I finally took it apart and found that one of the gears was off one tooth. I then bought a GRS scope for engraving. I just use the AM...
  2. Replies
    11
    Views
    750

    Question: Brian. I am engraving a colt walker made by...

    Brian.
    I am engraving a colt walker made by Uberti. When I first got it the gun appeared to be case hardened but to my surprise it is soft as butter. It is not case hardened but looks like it....
  3. Replies
    11
    Views
    750

    Question: Brian. I do all my own color case hardening. The...

    Brian. I do all my own color case hardening. The colors can be produced at a lower temp. You can get good colors by quenching at about 1250 but I have never tried going below that temp. I doubt if...
  4. Replies
    7
    Views
    615

    Like I said, Just stand the graver up so that the...

    Like I said, Just stand the graver up so that the face of the graver is vertical with the end line of the cut. Then stop and trim off the chip level with the surface from one side or the other. If...
  5. Replies
    7
    Views
    615

    I don't flip that chip out. I just stand the...

    I don't flip that chip out. I just stand the graver up at the end of the cut and then trim off the chip with the flat, flush with the surface. On inside corners, are you talking about serifs
  6. Replies
    7
    Views
    615

    I think what we need is a better explanation of...

    I think what we need is a better explanation of what you are trying to do.
  7. Thread: .410

    by jerrywh
    Replies
    19
    Views
    1,351

    That chisel work is out of this world.

    That chisel work is out of this world.
  8. Thread: Inlay Punches

    by jerrywh
    Replies
    21
    Views
    1,441

    I don't use hammers under the scope. Try using a...

    I don't use hammers under the scope. Try using a flat piece of steel bar about 1" wide and 1/4" thick. It will give you a lot more room to work without hitting the scope with the hammers. Also when...
  9. Thread: Inlay Punches

    by jerrywh
    Replies
    21
    Views
    1,441

    When you make your brass punches be sure to round...

    When you make your brass punches be sure to round off the edges of the punches. don;t leave any sharp edges on the punches. That will help stop the problem on denting the work piece. Sounds like you...
  10. Thread: Micro-Welding

    by jerrywh
    Replies
    9
    Views
    808

    I have done the caliber designation with steel or...

    I have done the caliber designation with steel or iron inlays. I can tig most other stuff but a micro welder can do most anything. there are guys who can weld up one point on a metal checkering job.
  11. Replies
    18
    Views
    1,295

    You will also need 10 power eye pieces. To obtain...

    You will also need 10 power eye pieces. To obtain the proper distance. I sometimes use 20 power eye pieces for more distance but you will loose magnification of you do.
  12. Thread: Micro-Welding

    by jerrywh
    Replies
    9
    Views
    808

    What is it that you need micro welded? Just...

    What is it that you need micro welded? Just curious?
  13. Question: That Nile gun is the best I have ever seen. My...

    That Nile gun is the best I have ever seen. My web site is down so I don't have any photos but when I do bolino I use The same graver as Coggan but I use the scope on about 10 power. I don't see...
  14. Question: Might as well use a cold chisel as a rotary tool.

    Might as well use a cold chisel as a rotary tool.
  15. Replies
    23
    Views
    3,038

    Thanks for the tips Sam.

    Thanks for the tips Sam.
  16. Replies
    23
    Views
    3,038

    Sam. I am interested in the scribe method you...

    Sam. I am interested in the scribe method you use. Is this scribe an ordinary shaped scribe. Is it ground differently. Do you normally use more than one pass with it. Can you elaborate some please.
  17. Replies
    11
    Views
    1,209

    foget all the soap and ans stuff, Just clean with...

    foget all the soap and ans stuff, Just clean with good strong alcohol. I had trouble the other day and all I did was change mi black ink cartridge, than it worked fine. the ink cartridge must be...
  18. Replies
    23
    Views
    3,038

    Ok I get it. I usually use undercutting chisels,...

    Ok I get it. I usually use undercutting chisels, Like Sam says I am very careful not to scar the edges of the letters or design. I have some very small undercutting Chisels that I sharpen under the...
  19. Replies
    15
    Views
    1,593

    Brian. Thanks for the great idea. Super good...

    Brian. Thanks for the great idea. Super good idea. I just want to tell you that you are one of the best in my opinion. Everything you do is superb. I want to get over there and see you some day....
  20. Replies
    15
    Views
    1,593

    Yes it is to obtain any size of wire you desire...

    Yes it is to obtain any size of wire you desire without waiting 10 days for a piece you need. Some times you only need a piece 2" long. Then what?
Results 1 to 20 of 100
Page 1 of 5 1 2 3 4


Lettering for Hand Engravers


Jumbo Pin Plates


Lee Griffiths


GRS Skyscraper

Cafe page views since 18-Nov-2006.