The Engraver's Cafe - The World's Largest Hand Engraving Community - Luca Casari engraved Italian Art Knives by Fabrizio Silvestrelli

Hand Engraving Forum Tips Archive Buy & Sell Interviews iGraver Tutorials Links Gallery Who's Online Top Posters Like Stats Advertise Polls

Hand Engraving Categories

Bracelets (38)

Buckles (28)

Drawings/Layout (57)

Gun Engraving (151)

Hobo Nickels (81)

Jewelry Engraving (48)

Knife Engraving (167)

Musical Instruments (23)

Other (191)

Pendants (45)

Rings (47)

Scrimshaw (27)

Tips & Tricks (10)

Watches (16)

Western (62)
Site Sponsors
Mission Statement

The Engraver's Cafe is an online community of hand engravers, jewelers, artists, carvers, scrimshanders, collectors, and craftsmen dedicated to the exchange of ideas and information relating to all aspects of the hand engraving art. Our mission is to provide a relaxed and friendly forum where friends from all over the world gather and share tehnique, photos, tips and tricks, while extending a helping hand to those starting their hand engraving journey.

Members Online Now
There are currently 55 users online. 12 members and 43 guests

Most users ever online was 1,983, 03-21-2012 at 12:18 AM.

‎theresamarieus

‎Dave London

‎dlilazteca

‎Roger B

‎myxlplyk

‎Dale Hatfield

‎l. bacon

‎nessa87

‎fegarex

‎Red Green

‎John P. Anderson
Latest Posts

Rt nailed it.

Rt nailed it.
Haraga.com 05-21-2013, 02:58 AM

Try this trick I learned from Ford Hallam - color...

Try this trick I learned from Ford Hallam - color the wire with a black Sharpie permanent marker (I've tried it successfully with gold, silver and copper). Put the wire in a small tin can (I use an...
tsterling 05-21-2013, 02:49 AM

Jared I have soldered different metals to...

Jared
I have soldered different metals to stainless using high temp silver solder. Usually 45% using Ultra flux it is Engelhard product I get at the welding supply store. Goes on like it would any...
RT Bit and Spur 05-21-2013, 02:40 AM

Ray Cover Has a casting with clouds, water .

Ray Cover
Has a casting with clouds, water .
Dave London 05-21-2013, 01:57 AM

Thanks. I have time to deduct a suitable point of...

Thanks. I have time to deduct a suitable point of attack. Will weigh out my options, now I have so many. Again thanks everyone .
Jared Eason 05-21-2013, 01:40 AM

Hi, check out Muggy Welding. It seems...

Hi,

check out Muggy Welding.

It seems they have some incredable fluxes and alloys for soldering all types of metals at low temps with very acceptable bonding strengths..

Link:...
airamp 05-20-2013, 11:59 PM

Amen to that!

Amen to that!
Roger Bleile 05-20-2013, 11:46 PM

I use a 100 grit on the drill press set up. I use...

I use a 100 grit on the drill press set up. I use it just for hogging off the excess on the top facets then go to the power hone with 260 then 1200. I finish with the 2000 bench stone for the heel....
Roger Bleile 05-20-2013, 11:44 PM

looks great!

looks great!
didyoung 05-20-2013, 11:24 PM

Not sure about Deleware precisely, but there are...

Not sure about Deleware precisely, but there are MANY engravers within a few hours drive from where you are. I'm sure that someone will speak up and show you at least a little and let you give it a...
diandwill 05-20-2013, 10:09 PM

Luca Casari engraved Italian Art Knives by Fabrizio Silvestrelli
by
martinr

View Profile

View Forum Posts

Private Message

View Blog Entries

View Articles
Published on 08-04-2012 02:36 PM Number of Views: 651

0 Comments
Just in from Italian knifemaker Fabrizio Silvestrelli (Silvester Knives) is this new pair of knives engraved by Luca Casari of Beretta. I have a feeling you guys and gals are going to like these. 4" blade length and 9 1/4" overall, they're two of the nicest knives in my small collection.

_{This article was originally published in forum thread:

Luca Casari engraved Italian Art Knives by Fabrizio Silvestrelli
started by
martinr} _{View original post}
Categories:
1. Knife Engraving

Tira

frontpage hit counter

Cafe page views since 18-Nov-2006.

All times are GMT. The time now is 03:49 AM.

© Copyright 2011 Sam Alfano - EngraversCafe.com - All rights reserved. No part of this site may be reproduced without the written permission of the owner.